Install Kubernetes Platform on All-in-one Simplex

Overview

The All-in-one Simplex (AIO-SX) deployment option provides all three cloud functions (controller, worker, and storage) on a single server with the following benefits:

  • Requires only a small amount of cloud processing and storage power

  • Application consolidation using multiple containers or virtual machines on a single physical server

  • A storage backend solution using a single-node CEPH deployment

Note

If you are behind a corporate firewall or proxy, you need to set proxy settings. Refer to Docker Proxy Configuration for details.

All-in-one Simplex deployment configuration

Figure 1: All-in-one Simplex deployment configuration

An AIO-SX deployment gives no protection against overall server hardware fault. Hardware component protection can be enabled with, for example, a hardware RAID or 2x Port LAG in the deployment.

Note

By default, StarlingX uses IPv4. To use StarlingX with IPv6:

  • The entire infrastructure and cluster configuration must be IPv6, with the exception of the PXE boot network.

  • Not all external servers are reachable via IPv6 addresses (for example Docker registries). Depending on your infrastructure, it may be necessary to deploy a NAT64/DNS64 gateway to translate the IPv4 addresses to IPv6.

For information on getting started quicky using an automated virtual installation, see Automated Virtual Installation.

Minimum hardware requirements

The recommended minimum hardware requirements for bare metal servers for various host types are:

Minimum Requirements

All-in-one Controller Node

Number of servers

1

Minimum processor class

Dual-CPU Intel® Xeon® E5 26xx family (SandyBridge) 8 cores/socket

or

Single-CPU Intel® Xeon® D-15xx family, 8 cores (low-power/low-cost option)

Note

  • Platform: 1 physical core with HT enabled or 2 physical cores with HT disabled, (by default, configurable)

    The use of single physical core for platform function is only suitable for Intel® 4th Generation Xeon® Scalable Processors or above and should not be configured for previous Intel® Xeon® CPU families. For All-In-One systems with older generation processors, two physical cores (or more) must be configured.

  • Application: Remaining cores

Minimum memory

64 GB

  • Platform:

    • Socket 0: 10GB (by default, configurable)

    • Socket 1: 1GB (by default, configurable)

  • Application:

    • Socket 0: Remaining memory

    • Socket 1: Remaining memory

Primary disk

500 GB SSD or NVMe (see Configure NVMe Drive as Primary Disk)

Additional disks

  • 1 or more 500 GB (min. 10K RPM) for Ceph OSD

  • Recommended, but not required: 1 or more SSDs or NVMe drives for Ceph journals (min. 1024 MiB per OSD journal)

  • Recommended, but not required: 1 or more 500G HDs (min. 10K RPM), SSDs or NVMe drives for Container ephemeral disk storage.

  • For StarlingX OpenStack, we recommend 1 or more 500 GB (min. 10K RPM) for VM local ephemeral storage

Minimum network ports

  • MGMT: 1x1GE ( Recommended: MGMT 2x10GE LAG ) Only required if subcloud is in Distributed Cloud.

  • OAM: 1x1GE (Recommended: OAM: 2x1GE LAG)

  • Data: 1 or more x 10GE (Recommended: Data: 2x10GE LAG)

USB

1 (Only required if used for initial installation of controller-0).

Power profile

C-states (up to C6) may be configured for some use cases where application workloads can tolerate additional scheduling/timer latency.

Note

C-states may be enabled depending on application requirements.

Boot order

HD, PXE, USB

BIOS mode

BIOS or UEFI

Note

UEFI Secure Boot and UEFI PXE boot over IPv6 are not supported. On systems with an IPv6 management network, you can use a separate IPv4 network for PXE boot. For more information, see PXE Boot Controller-0.

BIOS settings

  • Hyper-Threading technology enabled

  • Virtualization technology enabled

  • VT for directed I/O enabled

  • CPU power and performance policy set to performance

  • Minimum Processor Idle Power; CPU C state control disabled

  • Plug & play BMC detection disabled

Note

The system will not override the recommended BIOS settings.

Installation Prerequisites

Several pre-requisites must be completed prior to starting the StarlingX installation.

Before attempting to install StarlingX, ensure that you have the following:

  • The StarlingX host installer ISO image file.

  • The update-iso.sh script.

  • Optionally, if required, update the ISO image to modify installation boot parameters, automatically select boot menu options and/or add a kickstart file to automatically perform configurations such as configuring the initial IP Interface for bootstrapping.

    Use the update-iso.sh script from a StarlingX mirror. The script syntax and options are:

    update-iso.sh --initial-password <password> -i <input bootimage.iso> -o <output bootimage.iso>
    [ -a <ks-addon.cfg> ] [ -p param=value ]
    [ -d <default menu option> ] [ -t <menu timeout> ]
    -i <file>: Specify input ISO file
    -o <file>: Specify output ISO file
    -a <file>: Specify ks-addon.cfg file
    --initial-password <password>: Specify the initial login password for sysadmin user
    -p <p=v>:  Specify boot parameter

    Example:
        -p instdev=/dev/disk/by-path/pci-0000:00:0d.0-ata-1.0

    -d <default menu option>:
        Specify default boot menu option:
        0 - Standard Controller, Serial Console
        1 - Standard Controller, Graphical Console
        2 - AIO, Serial Console
        3 - AIO, Graphical Console
        4 - AIO Low-latency, Serial Console
        5 - AIO Low-latency, Graphical Console
        NULL - Clear default selection
    -t <menu timeout>:
        Specify boot menu timeout, in seconds

    The following example ks-addon.cfg file, used with the -a option, sets up an initial IP interface at boot time by defining a VLAN on an Ethernet interface with with static assigned VLAN addresses:

    #### start ks-addon.cfg
RAW_DEV=enp24s0f0
OAM_VLAN=103
MGMT_VLAN=163

cat << EOF > ${IMAGE_ROOTFS}/etc/network/interfaces.d/auto
auto ${RAW_DEV} lo vlan${OAM_VLAN} vlan${MGMT_VLAN}

EOF

cat << EOF > ${IMAGE_ROOTFS}/etc/network/interfaces.d/ifcfg-${RAW_DEV}
iface ${RAW_DEV} inet manual
mtu 9000
post-up echo 0 > /proc/sys/net/ipv6/conf/${RAW_DEV}/autoconf;\
echo 0 > /proc/sys/net/ipv6/conf/${RAW_DEV}/accept_ra;\
echo 0 > /proc/sys/net/ipv6/conf/${RAW_DEV}/accept_redirects
EOF

cat << EOF > ${IMAGE_ROOTFS}/etc/network/interfaces.d/ifcfg-vlan${OAM_VLAN}
iface vlan${OAM_VLAN} inet6 static
vlan-raw-device ${RAW_DEV}
address <__address__>
netmask 64
gateway <__address__>
mtu 1500
post-up /usr/sbin/ip link set dev vlan${OAM_VLAN} mtu 1500;\
echo 0 > /proc/sys/net/ipv6/conf/vlan${OAM_VLAN}/autoconf;\
echo 0 > /proc/sys/net/ipv6/conf/vlan${OAM_VLAN}/accept_ra;\
echo 0 > /proc/sys/net/ipv6/conf/vlan${OAM_VLAN}/accept_redirects
pre-up /sbin/modprobe -q 8021q
EOF

cat << EOF > ${IMAGE_ROOTFS}/etc/network/interfaces.d/ifcfg-vlan${MGMT_VLAN}
iface vlan${MGMT_VLAN} inet6 static
vlan-raw-device ${RAW_DEV}
address <__address__>
netmask 64
mtu 1500
post-up /usr/local/bin/tc_setup.sh vlan${MGMT_VLAN} mgmt 10000 > /dev/null;\
/usr/sbin/ip link set dev vlan${MGMT_VLAN} mtu 1500;\
echo 0 > /proc/sys/net/ipv6/conf/vlan${MGMT_VLAN}/autoconf;\
echo 0 > /proc/sys/net/ipv6/conf/vlan${MGMT_VLAN}/accept_ra;\
echo 0 > /proc/sys/net/ipv6/conf/vlan${MGMT_VLAN}/accept_redirects
pre-up /sbin/modprobe -q 8021q
EOF

#### end ks-addon.cfg

    After updating the ISO image, create a bootable USB with the ISO or put the ISO on a PXEBOOT server. See the next bullet for details.

  • A mechanism for boot installation of the StarlingX host installer ISO downloaded from a StarlingX mirror. This can be either:

    • a bootable USB drive with the StarlingX host installer ISO.

      Refer to Create Bootable USB for instructions on how to create a bootable USB with the StarlingX ISO on your system.

    • the ISO image on a PXE boot server on the same network as the server that will be used as the initial controller-0. See Appendix PXE Boot Controller-0 for details.

  • For all controller or AIO controller servers, OAM Network connectivity to:

    • the BMC ports of all nodes

    • An external DNS Server. This is required for accessing StarlingX Docker Registry as discussed below.

    • A Docker Registry(s) containing the Docker images for the StarlingX load accessible via the OAM Network.

    You can use one of the following options:

    • The public open source registries (i.e. docker.io, k8s.gcr.io, ghcr.io, gcr.io, quay.io). This is the default option.

    • A private Docker Registry populated with the docker images from the public open source registries.

  • A record of the IP addresses allocated for the public interfaces for your deployment (that is IP addresses for the OAM Network and SR-IOV Data Networks).

Prepare Servers for Installation

Preparing servers is the first step of the StarlingX installation procedure.

Prior to starting the StarlingX installation, ensure that the bare metal servers are in the following state:

  • Physically installed.

  • Cabled for power.

  • Cabled for networking.

    Far-end switch ports should be properly configured to realize the networking shown in the diagram earlier in this topic.

  • All disks are wiped.

    This ensures that servers will boot from either the network or USB storage, if present.

    Note

    The disks and disk partitions need to be wiped before the install. Installing a Debian ISO may fail with a message that the system is in emergency mode if the disks and disk partitions are not completely wiped before the install, especially if the server was previously running a CentOS ISO.

  • BIOS configured with Intel Virtualization (VTD, VTX)

    • Disabled for controller-only servers and storage servers.

    • Enabled for controller+worker (All-in-one) servers and worker servers.

  • The servers are powered off.

Install Software on Controller-0

Note

The disks and disk partitions need to be wiped before the install. Installing a Debian ISO may fail with a message that the system is in emergency mode if the disks and disk partitions are not completely wiped before the install, especially if the server was previously running a CentOS ISO.

  1. Insert the bootable USB into a bootable USB port on the host you are configuring as controller-0.

    Note

    Refer to Create Bootable USB for instructions on how to create a bootable USB with the StarlingX ISO.

    Note

    Alternatively one can PXEBOOT controller-0. See PXE Boot Controller-0 for details on how to setup a PXEBOOT Server and pxe-boot the StarlingX load on controller-0

  2. Power on the host.

  3. Attach to a console, ensure the host boots from the USB, and wait for the StarlingX Installer Menus.

  4. Wait for the Install menus, and when prompted, make the following menu selections in the installer:

    Note

    If you configured the default menu options into the ISO with the update-iso.sh script (using the -d option) in Installation Prerequisites, then the Install menu will not appear.

    1. Select the appropriate deployment option for your scenario.

      For All-in-one deployments, choose one of the All-in-One Configurations, either standard kernel or real-time/low-latency kernel.

      Standard Controller Configuration

      For a standard configuration with controller or dedicated storage.

      All-in-one Controller Configuration

      For an AIO Simplex or Duplex configuration.

      All-in-one Controller Configuration (Low Latency)

      For an AIO Simplex or Duplex configuration with Low Latency Kernel.

    2. Choose Graphical Console or Serial Console depending on your terminal access to the console port.

    Wait for non-interactive install of software to complete and server to reboot. This can take 5-10 minutes, depending on the performance of the server.

    Wait for the non-interactive software installation to complete and for the server to reboot. This can take 5-10 minutes, depending on the performance of the server.

    Warning

    When using the low latency kernel, you must use the serial console instead of the graphics console, as it causes RT performance issues.

Bootstrap system on controller-0

  1. Login using the username / password of “sysadmin” / “sysadmin”. When logging in for the first time, you will be forced to change the password.

    Login: sysadmin
Password:
Changing password for sysadmin.
(current) UNIX Password: sysadmin
New Password:
(repeat) New Password:

  2. Verify and/or configure IP connectivity.

    External connectivity is required to run the Ansible bootstrap playbook. The StarlingX boot image will DHCP out all interfaces so the server may have obtained an IP address and have external IP connectivity if a DHCP server is present in your environment. Verify this using the ip addr and ping 8.8.8.8 commands.

    Otherwise, manually configure an IP address and default IP route. Use the PORT, IP-ADDRESS/SUBNET-LENGTH and GATEWAY-IP-ADDRESS applicable to your deployment environment.

    sudo ip address add <IP-ADDRESS>/<SUBNET-LENGTH> dev <PORT>
sudo ip link set up dev <PORT>
sudo ip route add default via <GATEWAY-IP-ADDRESS> dev <PORT>
ping 8.8.8

  3. Specify user configuration overrides for the Ansible bootstrap playbook.

    Ansible is used to bootstrap StarlingX on controller-0. Key files for Ansible configuration are:

    /etc/ansible/hosts

    The default Ansible inventory file. Contains a single host: localhost.

    /usr/share/ansible/stx-ansible/playbooks/bootstrap.yml

    The Ansible bootstrap playbook.

    /usr/share/ansible/stx-ansible/playbooks/host_vars/bootstrap/default.yml

    The default configuration values for the bootstrap playbook.

    sysadmin home directory ($HOME)

    The default location where Ansible looks for and imports user configuration override files for hosts. For example: $HOME/<hostname>.yml.

    Important

    Some Ansible bootstrap parameters cannot be changed or are very difficult to change after installation is complete.

    Review the set of install-time-only parameters before installation and confirm that your values for these parameters are correct for the desired installation.

    Refer to Ansible install-time-only parameters for details.

    Specify the user configuration override file for the Ansible bootstrap playbook using one of the following methods:

    Note

    This Ansible Overrides file for the Bootstrap Playbook ($HOME/localhost.yml) contains security sensitive information, use the ansible-vault create $HOME/localhost.yml command to create it. You will be prompted for a password to protect/encrypt the file. Use the ansible-vault edit $HOME/localhost.yml command if the file needs to be edited after it is created.

    1. Use a copy of the default.yml file listed above to provide your overrides.

      The default.yml file lists all available parameters for bootstrap configuration with a brief description for each parameter in the file comments.

      To use this method, run the ansible-vault create $HOME/localhost.yml command and copy the contents of the default.yml file into the ansible-vault editor, and edit the configurable values as required.

    2. Create a minimal user configuration override file.

      To use this method, create your override file with the ansible-vault create $HOME/localhost.yml command and provide the minimum required parameters for the deployment configuration as shown in the example below. Use the OAM IP SUBNET and IP ADDRESSing applicable to your deployment environment.

      Note

      During system bootstrap, the platform does not support the use of quotation characters in the keystone user password.

      cd ~

cat <<EOF > localhost.yml

system_mode: simplex

dns_servers:
  - 8.8.8.8
  - 8.8.4.4

external_oam_subnet: <OAM-IP-SUBNET>/<OAM-IP-SUBNET-LENGTH>
external_oam_gateway_address: <OAM-GATEWAY-IP-ADDRESS>
external_oam_floating_address: <OAM-FLOATING-IP-ADDRESS>

admin_username: admin
admin_password: <admin-password>
ansible_become_pass: <sysadmin-password>

# OPTIONALLY provide a ROOT CA certificate and key for k8s root ca,
# if not specified, one will be auto-generated,
# see ‘Kubernetes Root CA Certificate’ in Security Guide for details.
k8s_root_ca_cert: < your_root_ca_cert.pem >
k8s_root_ca_key: < your_root_ca_key.pem >
apiserver_cert_sans:
  - < your_hostname_for_oam_floating.your_domain >

EOF

      In either of the above options, the bootstrap playbook’s default values will pull all container images required for the StarlingX Platform from Docker hub

      If you have setup a private Docker registry to use for bootstrapping then you will need to add the following lines in $HOME/localhost.yml:

      docker_registries:
  quay.io:
    url: myprivateregistry.abc.com:9001/quay.io
  docker.elastic.co:
    url: myprivateregistry.abc.com:9001/docker.elastic.co
  gcr.io:
    url: myprivateregistry.abc.com:9001/gcr.io
  ghcr.io:
    url: myprivateregistry.abc.com:9001/ghcr.io
  k8s.gcr.io:
    url: myprivateregistry.abc.com:9001/k8s.gcr.io
  docker.io:
    url: myprivateregistry.abc.com:9001/docker.io
  registry.k8s.io:
    url: myprivateregistry.abc.com:9001/registry.k8s.io
  icr.io:
    url: myprivateregistry.abc.com:9001/icr.io
  defaults:
    type: docker
    username: <your_myprivateregistry.abc.com_username>
    password: <your_myprivateregistry.abc.com_password>

# Add the CA Certificate that signed myprivateregistry.abc.com’s
# certificate as a Trusted CA
ssl_ca_cert: /home/sysadmin/myprivateregistry.abc.com-ca-cert.pem

      See Use a Private Docker Registry for more information.

      If a firewall is blocking access to Docker hub or your private registry from your StarlingX deployment, you will need to add the following lines in $HOME/localhost.yml (see Docker Proxy Configuration for more details about Docker proxy settings):

      # Add these lines to configure Docker to use a proxy server
docker_http_proxy: http://my.proxy.com:1080
docker_https_proxy: https://my.proxy.com:1443
docker_no_proxy:
   - 1.2.3.4

      Refer to Ansible Bootstrap Configurations for information on additional Ansible bootstrap configurations for advanced Ansible bootstrap scenarios.

  4. Run the Ansible bootstrap playbook:

    Note

    Before running the Ansible bootstrap playbook, it is important that you ensure that controller-0 server time is synchronized correctly. Run the following command:

    # check the current server time
$ date

# if the current server time is not correct, update with NTP

      # first add nameserver for DNS resolution
      $ echo "nameserver 8.8.8.8" >> /etc/resolv.conf
      $ echo "nameserver 8.8.4.4" >> /etc/resolv.conf

      # run ntpdate
      $ sudo ntpdate 0.pool.ntp.org 1.pool.ntp.org

    ansible-playbook --ask-vault-pass /usr/share/ansible/stx-ansible/playbooks/bootstrap.yml

    Wait for Ansible bootstrap playbook to complete. This can take 5-10 minutes, depending on the performance of the host machine.

Configure controller-0

The newly installed controller needs to be configured.

  1. Acquire admin credentials:

    source /etc/platform/openrc

  2. Configure the OAM interface of controller-0 and specify the attached network as “oam”.

    The following example configures the OAM interface on a physical untagged ethernet port, use OAM port name that is applicable to your deployment environment, for example eth0:

    ~(keystone_admin)$ OAM_IF=<OAM-PORT>
~(keystone_admin)$ system host-if-modify controller-0 $OAM_IF -c platform
~(keystone_admin)$ system interface-network-assign controller-0 $OAM_IF oam

    To configure a vlan or aggregated ethernet interface, see Node Interfaces.

  3. Configure NTP servers for network time synchronization:

    ~(keystone_admin)$ system ntp-modify ntpservers=0.pool.ntp.org,1.pool.ntp.org

    To configure PTP instead of NTP, see PTP Server Configuration.

    ~(keystone_admin)$ system ntp-modify ntpservers=0.pool.ntp.org,1.pool.ntp.org

    To configure PTP instead of NTP, see PTP Server Configuration.

OpenStack-specific host configuration

Important

These steps are required only if the StarlingX OpenStack application (stx-openstack) will be installed.

  1. For OpenStack only: Assign OpenStack host labels to controller-0 in support of installing the stx-openstack manifest and helm-charts later.

    ~(keystone_admin)$ system host-label-assign controller-0 openstack-control-plane=enabled
~(keystone_admin)$ system host-label-assign controller-0 openstack-compute-node=enabled
~(keystone_admin)$ system host-label-assign controller-0 openvswitch=enabled

    Note

    If you have a NIC that supports SR-IOV, then you can enable it by using the following:

    ~(keystone_admin)$ system host-label-assign controller-0 sriov=enabled

  2. For OpenStack only: Due to the additional OpenStack services running on the AIO controller platform cores, additional platform cores may be required.

    A minimum of 4 platform cores are required, 6 platform cores are recommended.

    Increase the number of platform cores with the following commands. This example assigns 6 cores on processor/numa-node 0 on controller-0 to platform.

    ~(keystone_admin)$ system host-cpu-modify -f platform -p0 6 controller-0

  3. Due to the additional OpenStack services’ containers running on the controller host, the size of the Docker filesystem needs to be increased from the default size of 30G to 60G.

    # check existing size of docker fs
system host-fs-list controller-0
# check available space (Avail Size (GiB)) in cgts-vg LVG where docker fs is located
system host-lvg-list controller-0
# if existing docker fs size + cgts-vg available space is less than
# 60G, you will need to add a new disk to cgts-vg.

   # Get device path of BOOT DISK
   system host-show controller-0 | fgrep rootfs

   # Get UUID of ROOT DISK by listing disks
   system host-disk-list controller-0

   # Add new disk to 'cgts-vg' local volume group
   system host-pv-add controller-0 cgts-vg <DISK_UUID>
   sleep 10    # wait for disk to be added

   # Confirm the available space and increased number of physical
   # volumes added to the cgts-vg colume group
   system host-lvg-list controller-0

# Increase docker filesystem to 60G
system host-fs-modify controller-0 docker=60

  4. For OpenStack only: Configure the system setting for the vSwitch.

    StarlingX has OVS (kernel-based) vSwitch configured as default:

    • Runs in a container; defined within the helm charts of stx-openstack manifest.

    • Shares the core(s) assigned to the platform.

    If you require better performance, OVS-DPDK (OVS with the Data Plane Development Kit, which is supported only on bare metal hardware) should be used:

    • Runs directly on the host (it is not containerized). Requires that at least 1 core be assigned/dedicated to the vSwitch function.

    To deploy the default containerized OVS:

    ~(keystone_admin)$ system modify --vswitch_type none

    This does not run any vSwitch directly on the host, instead, it uses the containerized OVS defined in the helm charts of stx-openstack manifest.

    To deploy OVS-DPDK, run the following command:

    ~(keystone_admin)$ system modify --vswitch_type ovs-dpdk

    Default recommendation for an AIO-controller is to use a single core for OVS-DPDK vSwitch.

    # assign 1 core on processor/numa-node 0 on controller-0 to vswitch
~(keystone_admin)$ system host-cpu-modify -f vswitch -p0 1 controller-0

    When using OVS-DPDK, configure 1G of huge pages for vSwitch memory on each NUMA node on the host. It is recommended to configure 1x 1G huge page (-1G 1) for vSwitch memory on each NUMA node on the host.

    However, due to a limitation with Kubernetes, only a single huge page size is supported on any one host. If your application VMs require 2M huge pages, then configure 500x 2M huge pages (-2M 500) for vSwitch memory on each NUMA node on the host.

    # Assign 1x 1G huge page on processor/numa-node 0 on controller-0 to vswitch
~(keystone_admin)$ system host-memory-modify -f vswitch -1G 1 controller-0 0

# Assign 1x 1G huge page on processor/numa-node 1 on controller-0 to vswitch
~(keystone_admin)$ system host-memory-modify -f vswitch -1G 1 controller-0 1

    Important

    VMs created in an OVS-DPDK environment must be configured to use huge pages to enable networking and must use a flavor with property: hw:mem_page_size=large Configure the huge pages for VMs in an OVS-DPDK environment on this host, the following commands are an example that assumes that 1G huge page size is being used on this host:

    # assign 1x 1G huge page on processor/numa-node 0 on controller-0 to applications
~(keystone_admin)$ system host-memory-modify -f application -1G 10 controller-0 0

# assign 1x 1G huge page on processor/numa-node 1 on controller-0 to applications
~(keystone_admin)$ system host-memory-modify -f application -1G 10 controller-0 1

    Note

    After controller-0 is unlocked, changing vswitch_type requires locking and unlocking controller-0 to apply the change.

  5. For OpenStack only: Add an instances filesystem or set up a disk based nova-local volume group, which is needed for stx-openstack nova ephemeral disks.

    Note

    Both cannot exist at the same time.

    Add an ‘instances’ filesystem

    ~(keystone_admin)$ export NODE=controller-0

# Create ‘instances’ filesystem
~(keystone_admin)$ system host-fs-add ${NODE} instances=<size>

    Or add a ‘nova-local’ volume group:

    ~(keystone_admin)$ export NODE=controller-0

# Create ‘nova-local’ local volume group
~(keystone_admin)$ system host-lvg-add ${NODE} nova-local

# Get UUID of an unused DISK to to be added to the ‘nova-local’ volume
# group. CEPH OSD Disks can NOT be used
# List host’s disks and take note of UUID of disk to be used
~(keystone_admin)$ system host-disk-list ${NODE}

# Add the unused disk to the ‘nova-local’ volume group
~(keystone_admin)$ system host-pv-add ${NODE} nova-local <DISK_UUID>

  6. For OpenStack only: Configure data interfaces for controller-0. Data class interfaces are vSwitch interfaces used by vSwitch to provide VM virtio vNIC connectivity to OpenStack Neutron Tenant Networks on the underlying assigned Data Network.

    Important

    A compute-labeled AIO-controller host MUST have at least one Data class interface.

    • Configure the data interfaces for controller-0.

      ~(keystone_admin)$  NODE=controller-0

# List inventoried host’s ports and identify ports to be used as ‘data’ interfaces,
# based on displayed linux port name, pci address and device type.
~(keystone_admin)$ system host-port-list ${NODE}

# List host’s auto-configured ‘ethernet’ interfaces,
# find the interfaces corresponding to the ports identified in previous step, and
# take note of their UUID
~(keystone_admin)$ system host-if-list -a ${NODE}

# Modify configuration for these interfaces
# Configuring them as ‘data’ class interfaces, MTU of 1500 and named data#
~(keystone_admin)$ system host-if-modify -m 1500 -n data0 -c data ${NODE} <data0-if-uuid>
~(keystone_admin)$ system host-if-modify -m 1500 -n data1 -c data ${NODE} <data1-if-uuid>

# Create Data Networks that vswitch 'data' interfaces will be connected to
~(keystone_admin)$ DATANET0='datanet0'
~(keystone_admin)$ DATANET1='datanet1'
~(keystone_admin)$ system datanetwork-add ${DATANET0} vlan
~(keystone_admin)$ system datanetwork-add ${DATANET1} vlan

# Assign Data Networks to Data Interfaces
~(keystone_admin)$ system interface-datanetwork-assign ${NODE} <data0-if-uuid> ${DATANET0}
~(keystone_admin)$ system interface-datanetwork-assign ${NODE} <data1-if-uuid> ${DATANET1}

Optionally Configure PCI-SRIOV Interfaces

  1. Optionally, configure PCI-SRIOV interfaces for controller-0.

    This step is optional for Kubernetes. Do this step if using SR-IOV network attachments in hosted application containers.

    This step is optional for OpenStack. Do this step if using SR-IOV vNICs in hosted application VMs. Note that PCI-SRIOV interfaces can have the same Data Networks assigned to them as vswitch data interfaces.

    1. Configure the PCI-SRIOV interfaces for controller-0.

      ~(keystone_admin)$ export NODE=controller-0

# List inventoried host’s ports and identify ports to be used as ‘pci-sriov’ interfaces,
# based on displayed linux port name, pci address and device type.
~(keystone_admin)$ system host-port-list ${NODE}

# List host’s auto-configured ‘ethernet’ interfaces,
# find the interfaces corresponding to the ports identified in previous step, and
# take note of their UUID
~(keystone_admin)$ system host-if-list -a ${NODE}

# Modify configuration for these interfaces
# Configuring them as ‘pci-sriov’ class interfaces, MTU of 1500 and named sriov#
~(keystone_admin)$ system host-if-modify -m 1500 -n sriov0 -c pci-sriov ${NODE} <sriov0-if-uuid> -N <num_vfs>
~(keystone_admin)$ system host-if-modify -m 1500 -n sriov1 -c pci-sriov ${NODE} <sriov1-if-uuid> -N <num_vfs>

# If not already created, create Data Networks that the 'pci-sriov' interfaces will
# be connected to
~(keystone_admin)$ DATANET0='datanet0'
~(keystone_admin)$ DATANET1='datanet1'
~(keystone_admin)$ system datanetwork-add ${DATANET0} vlan
~(keystone_admin)$ system datanetwork-add ${DATANET1} vlan

# Assign Data Networks to PCI-SRIOV Interfaces
~(keystone_admin)$ system interface-datanetwork-assign ${NODE} <sriov0-if-uuid> ${DATANET0}
~(keystone_admin)$ system interface-datanetwork-assign ${NODE} <sriov1-if-uuid> ${DATANET1}

    2. For Kubernetes Only: To enable using SR-IOV network attachments for the above interfaces in Kubernetes hosted application containers:

      1. Configure the Kubernetes SR-IOV device plugin.

        ~(keystone_admin)$ system host-label-assign controller-0 sriovdp=enabled

      2. Optional step: If you are planning on running DPDK in Kubernetes hosted application containers on this host, configure the number of 1G Huge pages required on both NUMA nodes.

        # assign 10x 1G huge page on processor/numa-node 0 on controller-0 to applications
~(keystone_admin)$ system host-memory-modify -f application controller-0 0 -1G 10

# assign 10x 1G huge page on processor/numa-node 1 on controller-0 to applications
~(keystone_admin)$ system host-memory-modify -f application controller-0 1 -1G

If required, initialize a Ceph-based Persistent Storage Backend

A persistent storage backend is required if your application requires PVCs.

Important

The StarlingX OpenStack application requires PVCs.

There are two options for persistent storage backend: the host-based Ceph solution and the Rook container-based Ceph solution.

For host-based Ceph:

  1. Add host-based Ceph backend:

    ~(keystone_admin)$ system storage-backend-add ceph --confirmed

  2. Add an OSD on controller-0 for host-based Ceph:

    # List host’s disks and identify disks you want to use for CEPH OSDs, taking note of their UUID
# By default, /dev/sda is being used as system disk and can not be used for OSD.
~(keystone_admin)$ system host-disk-list controller-0

# Add disk as an OSD storage
~(keystone_admin)$ system host-stor-add controller-0 osd <disk-uuid>

# List OSD storage devices
~(keystone_admin)$ system host-stor-list controller-0

For Rook container-based Ceph:

  1. Add Rook container-based backend:

    ~(keystone_admin)$ system storage-backend-add ceph-rook --confirmed

  2. Assign Rook host labels to controller-0 in support of installing the rook-ceph-apps manifest/helm-charts later:

    ~(keystone_admin)$ system host-label-assign controller-0 ceph-mon-placement=enabled
~(keystone_admin)$ system host-label-assign controller-0 ceph-mgr-placement=enabled

Unlock controller-0

Unlock controller-0 to bring it into service:

~(keystone_admin)$ system host-unlock controller-0

Controller-0 will reboot in order to apply configuration changes and come into service. This can take 5-10 minutes, depending on the performance of the host machine.

Complete system configuration by reviewing procedures in:

If using Rook container-based Ceph, finish configuring the ceph-rook Persistent Storage Backend

On controller-0:

  1. Wait for application rook-ceph-apps to be uploaded

    $ source /etc/platform/openrc
~(keystone_admin)$  system application-list
+---------------------+---------+-------------------------------+---------------+----------+-----------+
| application         | version | manifest name                 | manifest file | status   | progress  |
+---------------------+---------+-------------------------------+---------------+----------+-----------+
| oidc-auth-apps      | 1.0-0   | oidc-auth-manifest            | manifest.yaml | uploaded | completed |
| platform-integ-apps | 1.0-8   | platform-integration-manifest | manifest.yaml | uploaded | completed |
| rook-ceph-apps      | 1.0-1   | rook-ceph-manifest            | manifest.yaml | uploaded | completed |
+---------------------+---------+-------------------------------+---------------+----------+-----------+

  2. Configure rook to use /dev/sdb disk on controller-0 as a ceph OSD.

    ~(keystone_admin)$ system host-disk-wipe -s --confirm controller-0 /dev/sdb

    values.yaml for rook-ceph-apps.

    cluster:
  storage:
    nodes:
    - name: controller-0
      devices:
      - name: /dev/disk/by-path/pci-0000:00:03.0-ata-2.0

    ~(keystone_admin)$ system helm-override-update rook-ceph-apps rook-ceph kube-system --values values.yaml

  3. Apply the rook-ceph-apps application.

    ~(keystone_admin)$ system application-apply rook-ceph-apps

  4. Wait for OSDs pod to be ready.

    ~(keystone_admin)$ kubectl get pods -n kube-system
rook--ceph-crashcollector-controller-0-764c7f9c8-bh5c7   1/1     Running     0          62m
rook--ceph-mgr-a-69df96f57-9l28p                         1/1     Running     0          63m
rook--ceph-mon-a-55fff49dcf-ljfnx                        1/1     Running     0          63m
rook--ceph-operator-77b64588c5-nlsf2                     1/1     Running     0          66m
rook--ceph-osd-0-7d5785889f-4rgmb                        1/1     Running     0          62m
rook--ceph-osd-prepare-controller-0-cmwt5                0/1     Completed   0          2m14s
rook--ceph-tools-5778d7f6c-22tms                         1/1     Running     0          64m
rook--discover-kmv6c                                     1/1     Running     0          65m

Next steps

Your Kubernetes cluster is now up and running.

For instructions on how to access StarlingX Kubernetes see Access StarlingX Kubernetes.

For instructions on how to install and access StarlingX OpenStack see StarlingX OpenStack.