Upgrade All-in-One Duplex / Standard¶

You can upgrade the StarlingX Duplex or Standard configurations with a new release of StarlingX software.

Prerequisites

Perform a full backup to allow recovery.

Note

Back up files in the /home/sysadmin and /root directories prior to doing an upgrade. Home directories are not preserved during backup or restore operations, blade replacement, or upgrades.
The system must be “patch current”. All updates available for the current release running on the system must be applied, and all patches must be committed. To find and download applicable updates, visit the a StarlingX mirror.
Transfer the new release software load to controller-0 (or onto a USB stick); controller-0 must be active.

Note

Make sure that the /home/sysadmin directory has enough space (at least 2GB of free space), otherwise the upgrade may fail once it starts. If more space is needed, it is recommended to delete the .iso bootimage previously imported after the load-import command.
Transfer the new release software license file to controller-0, (or onto a USB stick).
Transfer the new release software signature to controller-0 (or onto a USB stick).
Unlock all hosts.
- All nodes must be unlocked. The upgrade cannot be started when there are locked nodes (the health check prevents it).

Note

The upgrade procedure includes steps to resolve system health issues.

Note

Upgrading hosts should be completed within 24 hours to avoid a kubeadm token timeout.

Procedure

Ensure that controller-0 is the active controller.

Install the license file for the release you are upgrading to, for example, nn.nn.

~(keystone_admin)]$ system license-install <license_file>

For example,

~(keystone_admin)]$ system license-install license.lic

Import the new release.

Run the load-import command on controller-0 to import the new release.

First, source /etc/platform/openrc. Also, you must specify an exact path to the *.iso bootimage file and to the *.sig bootimage signature file.

$ source /etc/platform/openrc
~(keystone_admin)]$ system load-import /home/sysadmin/<bootimage>.iso \
<bootimage>.sig
+--------------------+-----------+
| Property           | Value     |
+--------------------+-----------+
| id                 | 2         |
| state              | importing |
| software_version   | nn.nn     |
| compatible_version | nn.nn     |
| required_patches   |           |
+--------------------+-----------+

The load-import must be done on controller-0 and accepts relative paths.

Note

This will take a few minutes to complete.

Check to ensure the load was successfully imported.

~(keystone_admin)]$ system load-list
+----+----------+------------------+
| id | state    | software_version |
+----+----------+------------------+
| 1  | active   | nn.nn            |
| 2  | imported | nn.nn            |
+----+----------+------------------+

Apply any required software updates.

The system must be ‘patch current’. All software updates related to your current StarlingX software release must be uploaded, applied, and installed.

All software updates to the new StarlingX release, only need to be uploaded and applied. The install of these software updates will occur automatically during the software upgrade procedure as the hosts are reset to load the new release of software.

To find and download applicable updates, visit the a StarlingX mirror.

For more information, see Manage Software Updates.
Confirm that the system is healthy.

Check the current system health status, resolve any alarms and other issues reported by the system health-query-upgrade command, then recheck the system health status to confirm that all System Health fields are set to OK. For example:
```
~(keystone_admin)]$ system health-query-upgrade

System Health:
All hosts are provisioned: [OK]
All hosts are unlocked/enabled: [OK]
All hosts have current configurations: [OK]
All hosts are patch current: [OK]
Ceph Storage Healthy: [OK]
No alarms: [OK]
All kubernetes nodes are ready: [OK]
All kubernetes control plane pods are ready: [OK]
Required patches are applied: [OK]
License valid for upgrade: [OK]
No instances running on controller-1: [OK]
All kubernetes applications are in a valid state: [OK]
Active controller is controller-0: [OK]
```
By default, the upgrade process cannot be run and is not recommended to be run with active alarms present. Use the command system upgrade-start --force to force the upgrade process to start and ignore non-management-affecting alarms.

Note

It is strongly recommended that you clear your system of any and all alarms before doing an upgrade. While the --force option is available to run the upgrade, it is a best practice to clear any alarms.
Start the upgrade from controller-0.

Make sure that controller-0 is the active controller, and you are logged into controller-0 as sysadmin and your present working directory is your home directory.
```
~(keystone_admin)]$ system upgrade-start
+--------------+--------------------------------------+
| Property     | Value                                |
+--------------+--------------------------------------+
| uuid         | 61e5fcd7-a38d-40b0-ab83-8be55b87fee2 |
| state        | starting                             |
| from_release | nn.nn                                |
| to_release   | nn.nn                                |
+--------------+--------------------------------------+
```
This will make a copy of the upgrade data onto a DRBD file system to be used in the upgrade. Configuration changes are not allowed after this point until the swact to controller-1 is completed.

The following upgrade state applies once this command is executed:
- started:
  - State entered after system upgrade-start completes.
  - Release nn.nn system data (for example, postgres databases) has been exported to be used in the upgrade.
  - Configuration changes must not be made after this point, until the upgrade is completed.
As part of the upgrade, the upgrade process checks the health of the system and validates that the system is ready for an upgrade.

The upgrade process checks that no alarms are active before starting an upgrade.

Note

Use the command system upgrade-start --force to force the upgrade process to start and ignore non-management-affecting alarms. This should ONLY be done if you feel these alarms will not be an issue over the upgrades process.

On systems with Ceph storage, it also checks that the Ceph cluster is healthy.
Upgrade controller-1.
1. Lock controller-1.
```
~(keystone_admin)]$ system host-lock controller-1
```
2. Upgrade controller-1.
  
  Controller-1 installs the update and reboots, then performs data migration.
```
~(keystone_admin)]$ system host-upgrade controller-1
```
  Wait for controller-1 to reinstall with the load N+1 and becomes locked-disabled-online state.
  
  The following data migration states apply when this command is executed:
  - data-migration:
    - State entered when system host-upgrade controller-1 is executed.
    - System data is being migrated from release N to release N+1.
    Note
    
    The upgrade process will take a minimum of 20 to 30 minutes to complete.
    
    You can view the upgrade progress on controller-1 using the serial console.
  - data-migration-complete or upgrading-controllers:
    - State entered when controller-1 upgrade is complete.
    - System data has been successfully migrated from release nn.nn to release nn.nn.
  - data-migration-failed:
    - State entered if data migration on controller-1 fails.
    - Upgrade must be aborted.
    Note
    
    Review the /var/log/sysinv.log on the active controller for more details on data migration failure.
3. Check the upgrade state.
```
~(keystone_admin)]$ system upgrade-show
+--------------+--------------------------------------+
| Property     | Value                                |
+--------------+--------------------------------------+
| uuid         | e7c8f6bc-518c-46d4-ab81-7a59f8f8e64b |
| state        | data-migration-complete              |
| from_release | nn.nn                                |
| to_release   | nn.nn                                |
+--------------+--------------------------------------+
```
  If the upgrade-show status indicates ‘data-migration-failed’, then there is an issue with the data migration. Check the issue before proceeding to the next step.
4. Unlock controller-1.
```
~(keystone_admin)]$ system host-unlock controller-1
```
  Wait for controller-1 to become unlocked-enabled. Wait for the DRBD sync 400.001 Services-related alarm is raised and then cleared.
  
  The upgrading-controllers state applies when this command is executed. This state is entered after controller-1 has been upgraded to release nn.nn and data migration is successfully completed.
  
  If it transitions to unlocked-disabled-failed, check the issue before proceeding to the next step. The alarms may indicate a configuration error. Check the result of the configuration logs on controller-1, (for example, Error logs in controller1:/var/log/puppet).
Set controller-1 as the active controller. Swact to controller-1.
```
~(keystone_admin)]$ system host-swact controller-0
```
Wait until all services are enabled / active and the swact is complete on controller-0 before proceeding to the next step. Use the following command below:
```
~(keystone_admin)]$ system servicegroup-list
```
Upgrade controller-0.
1. Lock controller-0.
```
~(keystone_admin)]$ system host-lock controller-0
```
2. Upgrade controller-0.
```
~(keystone_admin)]$ system host-upgrade controller-0
```
3. Unlock controller-0.
```
~(keystone_admin)]$ system host-unlock controller-0
```
  Wait until the DRBD sync 400.001 Services-related alarm is raised and then cleared before proceeding to the next step.
  - upgrading-hosts:
    - State entered when both controllers are running release nn.nn software.
  Note
  
  AIO-DX or Controllers of Standard configurations can be upgraded, using steps 1-9 above.
Check the system health to ensure that there are no unexpected alarms.
```
~(keystone_admin)]$ fm alarm-list
```
Clear all alarms unrelated to the upgrade process.
If using Ceph storage backend, upgrade the storage nodes one at a time.

Note

Proceed to step 13 if no storage/worker node is present.

The storage node must be locked and all OSDs must be down in order to do the upgrade.
1. Lock storage-0.
```
~(keystone_admin)]$ system host-lock storage-0
```
2. Verify that the OSDs are down after the storage node is locked.
  
  In the Horizon interface, navigate to Admin > Platform > Storage Overview to view the status of the OSDs.
3. Upgrade storage-0.
```
~(keystone_admin)]$ system host-upgrade storage-0
```
  The upgrade is complete when the node comes online, and at that point, you can safely unlock the node.
  
  After upgrading a storage node, but before unlocking, there are Ceph synchronization alarms (that appear to be making progress in synching), and there are infrastructure network interface alarms (since the infrastructure network interface configuration has not been applied to the storage node yet, as it has not been unlocked).
  
  Unlock the node as soon as the upgraded storage node comes online.
4. Unlock storage-0.
```
~(keystone_admin)]$ system host-unlock storage-0
```
  Wait for all alarms to clear after the unlock before proceeding to upgrade the next storage host.
5. Repeat the above steps for each storage host.
  
  Note
  
  After upgrading the first storage node you can expect alarm 800.003. The alarm is cleared after all storage nodes are upgraded.
Upgrade worker hosts, one at a time, if any.
1. Lock worker-0.
```
~(keystone_admin)]$ system host-lock worker-0
```
2. Upgrade worker-0.
```
~(keystone_admin)]$ system host-upgrade worker-0
```
  Wait for the host to run the installer, reboot, and go online before unlocking it in the next step.
3. Unlock worker-0.
```
~(keystone_admin)]$ system host-unlock worker-0
```
  Wait for all alarms to clear after the unlock before proceeding to the next worker host.
4. Repeat the above steps for each worker host.
Set controller-0 as the active controller. Swact to controller-0.
```
~(keystone_admin)]$ system host-swact controller-1
```
Wait until services have gone active on the active controller-0 before proceeding to the next step. When all services on controller-0 are enabled-active, the swact is complete.
Activate the upgrade.
```
~(keystone_admin)]$ system upgrade-activate
+--------------+--------------------------------------+
| Property     | Value                                |
+--------------+--------------------------------------+
| uuid         | 61e5fcd7-a38d-40b0-ab83-8be55b87fee2 |
| state        | activating                           |
| from_release | nn.nn                                |
| to_release   | nn.nn                                |
+--------------+--------------------------------------+
```
During the running of the upgrade-activate command, new configurations are applied to the controller. 250.001 (hostname Configuration is out-of-date) alarms are raised and are cleared as the configuration is applied. The upgrade state goes from activating to activation-complete once this is done.

The following states apply when this command is executed.

activation-requested
State entered when system upgrade-activate is executed.

activating
State entered when we have started activating the upgrade by applying new configurations to the controller and compute hosts.

activating-hosts
State entered when applying host-specific configurations. This state is entered only if needed.

activation-complete
State entered when new configurations have been applied to all controller and compute hosts.
1. Check the status of the upgrade again to see it has reached activation-complete.
```
~(keystone_admin)]$ system upgrade-show
+--------------+--------------------------------------+
| Property     | Value                                |
+--------------+--------------------------------------+
| uuid         | 61e5fcd7-a38d-40b0-ab83-8be55b87fee2 |
| state        | activation-complete                  |
| from_release | nn.nn                                |
| to_release   | nn.nn                                |
+--------------+--------------------------------------+
```
Note

This can take more than half an hour to complete.

activation-failed
Check /var/log/sysinv.log for further information.

Complete the upgrade.

~(keystone_admin)]$ system upgrade-complete
+--------------+--------------------------------------+
| Property     | Value                                |
+--------------+--------------------------------------+
| uuid         | 61e5fcd7-a38d-40b0-ab83-8be55b87fee2 |
| state        | completing                           |
| from_release | nn.nn                                |
| to_release   | nn.nn                                |
+--------------+--------------------------------------+

Delete the imported load.

~(keystone_admin)]$ system load-list
+----+----------+------------------+
| id | state    | software_version |
+----+----------+------------------+
| 1  | imported | nn.nn            |
| 2  | active   | nn.nn            |
+----+----------+------------------+

~(keystone_admin)]$ system load-delete 1
Deleted load: load 1

Upgrade All-in-One Duplex / Standard

Upgrade All-in-One Duplex / Standard¶

StarlingX R6.0