Virtual All-in-one Duplex R2.0

Description

The All-in-one Duplex (AIO-DX) deployment option provides a pair of high availability (HA) servers with each server providing all three cloud functions (controller, compute, and storage).

An AIO-DX configuration provides the following benefits:

  • Only a small amount of cloud processing and storage power is required

  • Application consolidation using multiple virtual machines on a single pair of physical servers

  • High availability (HA) services run on the controller function across two physical servers in either active/active or active/standby mode

  • A storage back end solution using a two-node CEPH deployment across two servers

  • Virtual machines scheduled on both compute functions

  • Protection against overall server hardware fault, where

    • All controller HA services go active on the remaining healthy server

    • All virtual machines are recovered on the remaining healthy server

All-in-one Duplex deployment configuration

Figure 1: All-in-one Duplex deployment configuration

Note

By default, StarlingX uses IPv4. To use StarlingX with IPv6:

  • The entire infrastructure and cluster configuration must be IPv6, with the exception of the PXE boot network.

  • Not all external servers are reachable via IPv6 addresses (e.g. Docker registries). Depending on your infrastructure, it may be necessary to deploy a NAT64/DNS64 gateway to translate the IPv4 addresses to IPv6.

Physical host requirements and setup

This section describes:

  • System requirements for the workstation hosting the virtual machine(s) where StarlingX will be deployed

  • Host setup

Hardware requirements

The host system should have at least:

  • Processor: x86_64 only supported architecture with BIOS enabled hardware virtualization extensions

  • Cores: 8

  • Memory: 32GB RAM

  • Hard Disk: 500GB HDD

  • Network: One network adapter with active Internet connection

Software requirements

The host system should have at least:

  • A workstation computer with Ubuntu 16.04 LTS 64-bit

All other required packages will be installed by scripts in the StarlingX tools repository.

Host setup

Set up the host with the following steps:

  1. Update OS:

    apt-get update

  2. Clone the StarlingX tools repository:

    apt-get install -y git
cd $HOME
git clone https://opendev.org/starlingx/tools

  3. Install required packages:

    cd $HOME/tools/deployment/libvirt/
bash install_packages.sh
apt install -y apparmor-profiles
apt-get install -y ufw
ufw disable
ufw status

    Note

    On Ubuntu 16.04, if apparmor-profile modules were installed as shown in the example above, you must reboot the server to fully install the apparmor-profile modules.

  4. Get the StarlingX ISO. This can be from a private StarlingX build or from the public Cengn StarlingX build off ‘master’ branch, as shown below:

    wget http://mirror.starlingx.cengn.ca/mirror/starlingx/release/2.0.0/centos/outputs/iso/bootimage.iso

Prepare virtual environment and servers

On the host, prepare the virtual environment and virtual servers.

  1. Set up virtual platform networks for virtual deployment:

    bash setup_network.sh

  2. Create the XML definitions for the virtual servers required by this configuration option. This creates the XML virtual server definition for:

    • duplex-controller-0

    • duplex-controller-1

    The following command will start/virtually power on:

    • the ‘duplex-controller-0’ virtual server

    • the X-based graphical virt-manager application

    If there is no X-server present, then errors are returned.

    bash setup_configuration.sh -c duplex -i ./bootimage.iso

StarlingX Kubernetes

Install the StarlingX Kubernetes platform

Install software on controller-0

In the last step of “Prepare the virtual environment and virtual servers” the controller-0 virtual server ‘duplex-controller-0’ was started by the setup_configuration.sh command.

On the host, attach to the console of virtual controller-0 and select the appropriate installer menu options to start the non-interactive install of StarlingX software on controller-0.

Note

When entering the console, it is very easy to miss the first installer menu selection. Use ESC to navigate to previous menus, to ensure you are at the first installer menu.

virsh console duplex-controller-0

Make the following menu selections in the installer:

  1. First menu: Select ‘All-in-one Controller Configuration’

  2. Second menu: Select ‘Serial Console’

  3. Third menu: Select ‘Standard Security Profile’

Wait for the non-interactive install of software to complete and for the server to reboot. This can take 5-10 minutes, depending on the performance of the host machine.

Bootstrap system on controller-0

On virtual controller-0:

  1. Log in using the username / password of “sysadmin” / “sysadmin”. When logging in for the first time, you will be forced to change the password.

    Login: sysadmin
Password:
Changing password for sysadmin.
(current) UNIX Password: sysadmin
New Password:
(repeat) New Password:

  2. External connectivity is required to run the Ansible bootstrap playbook.

    export CONTROLLER0_OAM_CIDR=10.10.10.3/24
export DEFAULT_OAM_GATEWAY=10.10.10.1
sudo ip address add $CONTROLLER0_OAM_CIDR dev enp7s1
sudo ip link set up dev enp7s1
sudo ip route add default via $DEFAULT_OAM_GATEWAY dev enp7s1

  3. Specify user configuration overrides for the Ansible bootstrap playbook.

    Ansible is used to bootstrap StarlingX on controller-0. Key files for Ansible configuration are:

    /etc/ansible/hosts

    The default Ansible inventory file. Contains a single host: localhost.

    /usr/share/ansible/stx-ansible/playbooks/bootstrap/bootstrap.yml

    The Ansible bootstrap playbook.

    /usr/share/ansible/stx-ansible/playbooks/bootstrap/host_vars/default.yml

    The default configuration values for the bootstrap playbook.

    sysadmin home directory ($HOME)

    The default location where Ansible looks for and imports user configuration override files for hosts. For example: $HOME/<hostname>.yml.

    Specify the user configuration override file for the Ansible bootstrap playbook using one of the following methods:

    • Copy the default.yml file listed above to $HOME/localhost.yml and edit the configurable values as desired (use the commented instructions in the file).

    or

    • Create the minimal user configuration override file as shown in the example below:

      cd ~
cat <<EOF > localhost.yml
system_mode: duplex

dns_servers:
  - 8.8.8.8
  - 8.8.4.4

external_oam_subnet: 10.10.10.0/24
external_oam_gateway_address: 10.10.10.1
external_oam_floating_address: 10.10.10.2
external_oam_node_0_address: 10.10.10.3
external_oam_node_1_address: 10.10.10.4

admin_username: admin
admin_password: <sysadmin-password>
ansible_become_pass: <sysadmin-password>
EOF

    Additional Ansible bootstrap configurations for advanced use cases are available:

  4. Run the Ansible bootstrap playbook:

    ansible-playbook /usr/share/ansible/stx-ansible/playbooks/bootstrap/bootstrap.yml

    Wait for Ansible bootstrap playbook to complete. This can take 5-10 minutes, depending on the performance of the host machine.

Configure controller-0

On virtual controller-0:

  1. Acquire admin credentials:

    source /etc/platform/openrc

  2. Configure the OAM and MGMT interfaces of controller-0 and specify the attached networks:

    OAM_IF=enp7s1
MGMT_IF=enp7s2
system host-if-modify controller-0 lo -c none
IFNET_UUIDS=$(system interface-network-list controller-0 | awk '{if ($6=="lo") print $4;}')
for UUID in $IFNET_UUIDS; do
    system interface-network-remove ${UUID}
done
system host-if-modify controller-0 $OAM_IF -c platform
system interface-network-assign controller-0 $OAM_IF oam
system host-if-modify controller-0 $MGMT_IF -c platform
system interface-network-assign controller-0 $MGMT_IF mgmt
system interface-network-assign controller-0 $MGMT_IF cluster-host

  3. Configure NTP Servers for network time synchronization:

    Note

    In a virtual environment, this can sometimes cause Ceph clock skew alarms. Also, the virtual instances clock is synchronized with the host clock, so it is not absolutely required to configure NTP in this step.

    system ntp-modify ntpservers=0.pool.ntp.org,1.pool.ntp.org

  4. Configure data interfaces for controller-0.

    Important

    This step is required only if the StarlingX OpenStack application (stx-openstack) will be installed.

    1G Huge Pages are not supported in the virtual environment and there is no virtual NIC supporting SRIOV. For that reason, data interfaces are not applicable in the virtual environment for the Kubernetes-only scenario.

    For OpenStack only:

    DATA0IF=eth1000
DATA1IF=eth1001
export COMPUTE=controller-0
PHYSNET0='physnet0'
PHYSNET1='physnet1'
SPL=/tmp/tmp-system-port-list
SPIL=/tmp/tmp-system-host-if-list
system host-port-list ${COMPUTE} --nowrap > ${SPL}
system host-if-list -a ${COMPUTE} --nowrap > ${SPIL}
DATA0PCIADDR=$(cat $SPL | grep $DATA0IF |awk '{print $8}')
DATA1PCIADDR=$(cat $SPL | grep $DATA1IF |awk '{print $8}')
DATA0PORTUUID=$(cat $SPL | grep ${DATA0PCIADDR} | awk '{print $2}')
DATA1PORTUUID=$(cat $SPL | grep ${DATA1PCIADDR} | awk '{print $2}')
DATA0PORTNAME=$(cat $SPL | grep ${DATA0PCIADDR} | awk '{print $4}')
DATA1PORTNAME=$(cat  $SPL | grep ${DATA1PCIADDR} | awk '{print $4}')
DATA0IFUUID=$(cat $SPIL | awk -v DATA0PORTNAME=$DATA0PORTNAME '($12 ~ DATA0PORTNAME) {print $2}')
DATA1IFUUID=$(cat $SPIL | awk -v DATA1PORTNAME=$DATA1PORTNAME '($12 ~ DATA1PORTNAME) {print $2}')

system datanetwork-add ${PHYSNET0} vlan
system datanetwork-add ${PHYSNET1} vlan

system host-if-modify -m 1500 -n data0 -c data ${COMPUTE} ${DATA0IFUUID}
system host-if-modify -m 1500 -n data1 -c data ${COMPUTE} ${DATA1IFUUID}
system interface-datanetwork-assign ${COMPUTE} ${DATA0IFUUID} ${PHYSNET0}
system interface-datanetwork-assign ${COMPUTE} ${DATA1IFUUID} ${PHYSNET1}

  5. Add an OSD on controller-0 for ceph:

    system host-disk-list controller-0
system host-disk-list controller-0 | awk '/\/dev\/sdb/{print $2}' | xargs -i system host-stor-add controller-0 {}
system host-stor-list controller-0
OpenStack-specific host configuration

Important

This step is required only if the StarlingX OpenStack application (stx-openstack) will be installed.

  1. For OpenStack only: Assign OpenStack host labels to controller-0 in support of installing the stx-openstack manifest/helm-charts later.

    system host-label-assign controller-0 openstack-control-plane=enabled
system host-label-assign controller-0 openstack-compute-node=enabled
system host-label-assign controller-0 openvswitch=enabled
system host-label-assign controller-0 sriov=enabled

  2. For OpenStack only: A vSwitch is required.

    The default vSwitch is containerized OVS that is packaged with the stx-openstack manifest/helm-charts. StarlingX provides the option to use OVS-DPDK on the host, however, in the virtual environment OVS-DPDK is NOT supported, only OVS is supported. Therefore, simply use the default OVS vSwitch here.

  3. For OpenStack Only: Set up disk partition for nova-local volume group, which is needed for stx-openstack nova ephemeral disks.

    export COMPUTE=controller-0

echo ">>> Getting root disk info"
ROOT_DISK=$(system host-show ${COMPUTE} | grep rootfs | awk '{print $4}')
ROOT_DISK_UUID=$(system host-disk-list ${COMPUTE} --nowrap | grep ${ROOT_DISK} | awk '{print $2}')
echo "Root disk: $ROOT_DISK, UUID: $ROOT_DISK_UUID"

echo ">>>> Configuring nova-local"
NOVA_SIZE=34
NOVA_PARTITION=$(system host-disk-partition-add -t lvm_phys_vol ${COMPUTE} ${ROOT_DISK_UUID} ${NOVA_SIZE})
NOVA_PARTITION_UUID=$(echo ${NOVA_PARTITION} | grep -ow "| uuid | [a-z0-9\-]* |" | awk '{print $4}')
system host-lvg-add ${COMPUTE} nova-local
system host-pv-add ${COMPUTE} nova-local ${NOVA_PARTITION_UUID}
sleep 2

echo ">>> Wait for partition $NOVA_PARTITION_UUID to be ready."
while true; do system host-disk-partition-list $COMPUTE --nowrap | grep $NOVA_PARTITION_UUID | grep Ready; if [ $? -eq 0 ]; then break; fi; sleep 1; done

Unlock controller-0

Unlock virtual controller-0 to bring it into service:

system host-unlock controller-0

Controller-0 will reboot in order to apply configuration changes and come into service. This can take 5-10 minutes, depending on the performance of the host machine.

Install software on controller-1 node

  1. On the host, power on the controller-1 virtual server, ‘duplex-controller-1’. It will automatically attempt to network boot over the management network:

    virsh start duplex-controller-1

  2. Attach to the console of virtual controller-1:

    virsh console duplex-controller-1

    As controller-1 VM boots, a message appears on its console instructing you to configure the personality of the node.

  3. On the console of virtual controller-0, list hosts to see the newly discovered controller-1 host (hostname=None):

    system host-list
+----+--------------+-------------+----------------+-------------+--------------+
| id | hostname     | personality | administrative | operational | availability |
+----+--------------+-------------+----------------+-------------+--------------+
| 1  | controller-0 | controller  | unlocked       | enabled     | available    |
| 2  | None         | None        | locked         | disabled    | offline      |
+----+--------------+-------------+----------------+-------------+--------------+

  4. On virtual controller-0, using the host id, set the personality of this host to ‘controller’:

    system host-update 2 personality=controller

  5. Wait for the software installation on controller-1 to complete, controller-1 to reboot, and controller-1 to show as locked/disabled/online in ‘system host-list’. This can take 5-10 minutes, depending on the performance of the host machine.

    system host-list
+----+--------------+-------------+----------------+-------------+--------------+
| id | hostname     | personality | administrative | operational | availability |
+----+--------------+-------------+----------------+-------------+--------------+
| 1  | controller-0 | controller  | unlocked       | enabled     | available    |
| 2  | controller-1 | controller  | locked         | disabled    | online      |
+----+--------------+-------------+----------------+-------------+--------------+

Configure controller-1

On virtual controller-0:

  1. Configure the OAM and MGMT interfaces of controller-1 and specify the attached networks. Note that the MGMT interface is partially set up automatically by the network install procedure.

    OAM_IF=enp7s1
system host-if-modify controller-1 $OAM_IF -c platform
system interface-network-assign controller-1 $OAM_IF oam
system interface-network-assign controller-1 mgmt0 cluster-host

  2. Configure data interfaces for controller-1.

    Important

    This step is required only if the StarlingX OpenStack application (stx-openstack) will be installed.

    1G Huge Pages are not supported in the virtual environment and there is no virtual NIC supporting SRIOV. For that reason, data interfaces are not applicable in the virtual environment for the Kubernetes-only scenario.

    For OpenStack only:

    DATA0IF=eth1000
DATA1IF=eth1001
export COMPUTE=controller-1
PHYSNET0='physnet0'
PHYSNET1='physnet1'
SPL=/tmp/tmp-system-port-list
SPIL=/tmp/tmp-system-host-if-list
system host-port-list ${COMPUTE} --nowrap > ${SPL}
system host-if-list -a ${COMPUTE} --nowrap > ${SPIL}
DATA0PCIADDR=$(cat $SPL | grep $DATA0IF |awk '{print $8}')
DATA1PCIADDR=$(cat $SPL | grep $DATA1IF |awk '{print $8}')
DATA0PORTUUID=$(cat $SPL | grep ${DATA0PCIADDR} | awk '{print $2}')
DATA1PORTUUID=$(cat $SPL | grep ${DATA1PCIADDR} | awk '{print $2}')
DATA0PORTNAME=$(cat $SPL | grep ${DATA0PCIADDR} | awk '{print $4}')
DATA1PORTNAME=$(cat  $SPL | grep ${DATA1PCIADDR} | awk '{print $4}')
DATA0IFUUID=$(cat $SPIL | awk -v DATA0PORTNAME=$DATA0PORTNAME '($12 ~ DATA0PORTNAME) {print $2}')
DATA1IFUUID=$(cat $SPIL | awk -v DATA1PORTNAME=$DATA1PORTNAME '($12 ~ DATA1PORTNAME) {print $2}')

system datanetwork-add ${PHYSNET0} vlan
system datanetwork-add ${PHYSNET1} vlan

system host-if-modify -m 1500 -n data0 -c data ${COMPUTE} ${DATA0IFUUID}
system host-if-modify -m 1500 -n data1 -c data ${COMPUTE} ${DATA1IFUUID}
system interface-datanetwork-assign ${COMPUTE} ${DATA0IFUUID} ${PHYSNET0}
system interface-datanetwork-assign ${COMPUTE} ${DATA1IFUUID} ${PHYSNET1}

  3. Add an OSD on controller-1 for ceph:

    echo ">>> Add OSDs to primary tier"
system host-disk-list controller-1
system host-disk-list controller-1 | awk '/\/dev\/sdb/{print $2}' | xargs -i system host-stor-add controller-1 {}
system host-stor-list controller-1
OpenStack-specific host configuration

Important

This step is required only if the StarlingX OpenStack application (stx-openstack) will be installed.

  1. For OpenStack only: Assign OpenStack host labels to controller-1 in support of installing the stx-openstack manifest/helm-charts later:

    system host-label-assign controller-1 openstack-control-plane=enabled
system host-label-assign controller-1 openstack-compute-node=enabled
system host-label-assign controller-1 openvswitch=enabled
system host-label-assign controller-1 sriov=enabled

  2. For OpenStack only: Set up disk partition for nova-local volume group, which is needed for stx-openstack nova ephemeral disks:

    export COMPUTE=controller-1

echo ">>> Getting root disk info"
ROOT_DISK=$(system host-show ${COMPUTE} | grep rootfs | awk '{print $4}')
ROOT_DISK_UUID=$(system host-disk-list ${COMPUTE} --nowrap | grep ${ROOT_DISK} | awk '{print $2}')
echo "Root disk: $ROOT_DISK, UUID: $ROOT_DISK_UUID"

echo ">>>> Configuring nova-local"
NOVA_SIZE=34
NOVA_PARTITION=$(system host-disk-partition-add -t lvm_phys_vol ${COMPUTE} ${ROOT_DISK_UUID} ${NOVA_SIZE})
NOVA_PARTITION_UUID=$(echo ${NOVA_PARTITION} | grep -ow "| uuid | [a-z0-9\-]* |" | awk '{print $4}')
system host-lvg-add ${COMPUTE} nova-local
system host-pv-add ${COMPUTE} nova-local ${NOVA_PARTITION_UUID}

Unlock controller-1

Unlock virtual controller-1 in order to bring it into service:

system host-unlock controller-1

Controller-1 will reboot in order to apply configuration changes and come into service. This can take 5-10 minutes, depending on the performance of the host machine.

When it completes, your Kubernetes cluster is up and running.

Access StarlingX Kubernetes

Use local/remote CLIs, GUIs, and/or REST APIs to access and manage StarlingX Kubernetes and hosted containerized applications. Refer to details on accessing the StarlingX Kubernetes cluster in the Access StarlingX Kubernetes guide.

StarlingX OpenStack

Install StarlingX OpenStack

Other than the OpenStack-specific configurations required in the underlying StarlingX/Kubernetes infrastructure (described in the installation steps for the StarlingX Kubernetes platform above), the installation of containerized OpenStack for StarlingX is independent of deployment configuration. Refer to the Install OpenStack guide for installation instructions.

Access StarlingX OpenStack

Use local/remote CLIs, GUIs and/or REST APIs to access and manage StarlingX OpenStack and hosted virtualized applications. Refer to details on accessing StarlingX OpenStack in the Access StarlingX OpenStack guide.

Uninstall StarlingX OpenStack

Refer to the Uninstall OpenStack guide for instructions on how to uninstall and delete the OpenStack application.